Solar Tracker Controller User Manual
  • Home
  • Product Info
  • Where to Buy
Select Page

Commands or Data not reaching device

by Engineering | Aug 23, 2020 | Trouble Shooting 1 Axis-Group, Trouble Shooting 2 Axis-Group, Trouble Shooting Grid Connect-Group

Commands or Data not reaching device I enter Commands or Data and do not see any of the changes in my screen.  Trouble Shooting The cause most often is the screen is no longer updating. Refreshing through your browser or check the refresh button near the lower...

Brushless Motor Direction Change

by Alex Bryant | Mar 6, 2015 | 2 Axis Installation, 2 Axis Installation-Group, Brushless Motors, Trouble Shooting 1 Axis-Group

If the brushless motors for azimuth and altitude changes are not turning in the correct direction when using the manual switches use the following instructions to change the direction. The procedure involves switching the wiring for the reversing relays so that...

Power Supply Resets

by engineering | Feb 25, 2015 | Brushless Motors, Tech Support, Trouble Shooting 1 Axis-Group, Trouble Shooting 2 Axis-Group

PROBLEM: My power supply cuts out every time my brushless motor stops. The controller reboots as well.   POSSIBLE SOLUTION: Check that the current limit adjustment is set at 10 amps. As we use 10 amp motors there is no reason to set it higher as it can cause the...

Recent Posts

  • Controls -2032
  • 2 Axis Brush Motors (Sinking)
  • Commands or Data not reaching device
  • Single or Dual Tracker Controller
  • Setup & Configuration

Recent Comments

    Archives

    • November 2020
    • August 2020
    • May 2020
    • April 2020
    • January 2020
    • November 2019
    • October 2019
    • August 2019
    • July 2019
    • June 2019
    • May 2019
    • February 2019
    • August 2018
    • November 2017
    • September 2017
    • August 2017
    • July 2017
    • June 2017
    • December 2016
    • March 2015
    • February 2015
    • November 2013
    • October 2013
    • August 2013

    Categories

    • 1 Axis Configuration-Group
    • 1 Axis Installation
    • 1 Axis Installation-Group
    • 1 Axis Products-Group
    • 1 Axis Wiring Diagram-Group
    • 1200 QS-Group
    • 1200 Wiring Diagram-Group
    • 2 Axis Configuration-Group
    • 2 Axis Installation
    • 2 Axis Installation-Group
    • 2 Axis Products-Group
    • 2 Axis Wiring Diagram-Group
    • 2400 Wiring Diagram-Group
    • Accessories Wiring-Group
    • Accessories-Group
    • Anemometer-Group
    • Brushed Motor-Group
    • Brushless Motor-Group
    • Brushless Motors
    • Calibration 1060 Series-Group
    • Calibration 1200 Series-Group
    • Calibration 2400 Series-Group
    • certified template-group
    • Customer Support-Group
    • FAQ General-Group
    • Getting Started
    • Grid Connect Configuration-Group
    • Grid Connect Installation-Group
    • Grid Connect Wiring Diagram-Group
    • Installation WiFi-Group
    • IPm WebControl
    • Networking-Group
    • Operations 1 Axis-Group
    • Operations 2 Axis-Group
    • Physical Dimensions-Group
    • Product Specifications-Group
    • Products
    • Products-Group
    • QSG-Group
    • Quick Start Guides
    • Sensors-Group
    • Software Load Toolkit – Group
    • Tech Support
    • Trouble Shooting 1 Axis-Group
    • Trouble Shooting 2 Axis-Group
    • Trouble Shooting Grid Connect-Group
    • Trouble Shooting Networks-Group
    • Trouble Shooting WiFi-Group
    • Uncategorized

    Meta

    • Log in
    • Entries feed
    • Comments feed
    • WordPress.org