Solar Tracker Controller User Manual
  • Home
  • Product Info
  • Where to Buy
Select Page

Why does the tracker reach 45 deg. tilt earlier ?

by engineering | May 23, 2019 | FAQ General-Group

It seems to be earlier as summer approaches. Question: I’ve noticed a problem with our single axis tilt tracker that we replaced.  It’s begun reaching 45 degrees west earlier and earlier in the day rather than later, which you would expect going into summer.  A recent...

How do I know which LED represents what terminal?

by engineering | Nov 9, 2017 | FAQ General-Group

FAQ Corresponding Terminal No. to LED Terminal No. Type LED No. 1 DI0 1 31 DI1 2 2 DI2 3 32 DI3 4 3 DI4 5 33 DI5 6 4 DI6 7 34 DI7 8 5 DI8 9 35 DI9 10 6 DI10 11 36 DI11 12 7 DO0 1 37 DO1 2 8 DO2 3 38 DO3 4 9 AI0 1 39 AI1 2 10 AI2 3 40 AI3 4 11 AI4 5 41 AI5 6 12 AI6 7...

How many axis’ can a tracker control?

by engineering | Sep 29, 2017 | certified template-group, FAQ General-Group

General Category The Tracker IPm currently can control 2 axis’ simultaneously. These can be 1 Elevation & 1 Azimuth or 2 Elevation....

How does the Tracker identify the sun’s position?

by engineering | Sep 29, 2017 | certified template-group, FAQ General-Group

General Category The Tracker IPm uses the NREL Solar Positionin ALgorithm which calculates the sun’s position based on Latitude, Longitude, elevations and time of day. This calculation is compared to a feedback from an inclinometer for the Zenith Elevation and a...

What is the maximum distance the power signal can travel in a cable?

by engineering | Sep 29, 2017 | certified template-group, FAQ General-Group

General Category If your design has the controller and relays at some distance from the motor and you will be running the risk of diminished voltage of the DC power as the distance increases. There are very good Voltage Drop Calculators on the web such...

Recent Posts

  • Controls -2032
  • 2 Axis Brush Motors (Sinking)
  • Commands or Data not reaching device
  • Single or Dual Tracker Controller
  • Setup & Configuration

Recent Comments

    Archives

    • November 2020
    • August 2020
    • May 2020
    • April 2020
    • January 2020
    • November 2019
    • October 2019
    • August 2019
    • July 2019
    • June 2019
    • May 2019
    • February 2019
    • August 2018
    • November 2017
    • September 2017
    • August 2017
    • July 2017
    • June 2017
    • December 2016
    • March 2015
    • February 2015
    • November 2013
    • October 2013
    • August 2013

    Categories

    • 1 Axis Configuration-Group
    • 1 Axis Installation
    • 1 Axis Installation-Group
    • 1 Axis Products-Group
    • 1 Axis Wiring Diagram-Group
    • 1200 QS-Group
    • 1200 Wiring Diagram-Group
    • 2 Axis Configuration-Group
    • 2 Axis Installation
    • 2 Axis Installation-Group
    • 2 Axis Products-Group
    • 2 Axis Wiring Diagram-Group
    • 2400 Wiring Diagram-Group
    • Accessories Wiring-Group
    • Accessories-Group
    • Anemometer-Group
    • Brushed Motor-Group
    • Brushless Motor-Group
    • Brushless Motors
    • Calibration 1060 Series-Group
    • Calibration 1200 Series-Group
    • Calibration 2400 Series-Group
    • certified template-group
    • Customer Support-Group
    • FAQ General-Group
    • Getting Started
    • Grid Connect Configuration-Group
    • Grid Connect Installation-Group
    • Grid Connect Wiring Diagram-Group
    • Installation WiFi-Group
    • IPm WebControl
    • Networking-Group
    • Operations 1 Axis-Group
    • Operations 2 Axis-Group
    • Physical Dimensions-Group
    • Product Specifications-Group
    • Products
    • Products-Group
    • QSG-Group
    • Quick Start Guides
    • Sensors-Group
    • Software Load Toolkit – Group
    • Tech Support
    • Trouble Shooting 1 Axis-Group
    • Trouble Shooting 2 Axis-Group
    • Trouble Shooting Grid Connect-Group
    • Trouble Shooting Networks-Group
    • Trouble Shooting WiFi-Group
    • Uncategorized

    Meta

    • Log in
    • Entries feed
    • Comments feed
    • WordPress.org